Frequently asked questions (FAQ)

It replaces scattered individual pieces of information with a single technical reference. Planners, specialist contractors and building owners find the system concept, the layer structure, product information and application notes all in one place.

The handbook is aimed at architects, energy consultants, experts, specialist contractors, applicators and building owners. It makes technical relationships understandable and serves as the basis for application.

Nanofassadendämmung describes a three-stage PSCoat facade system consisting of a primer, a functional layer and a top coat.

The focus is not on a single product but on the complete system build-up. Each layer performs a defined task and is matched to the layer that follows.

The facade system consists of PSC 250 T ECB BASIC B, PSC 250 T BUILD and PSC 250 T ECO OUTSIDE.

mkm International GmbH handles sales and system support. Technical product responsibility lies with the manufacturer PSCoat Zurynski, Özdogan & Co. GmbH.

This introduction positions the system. The technical details, application requirements, safety information and product data follow in the subsequent chapters.

It consists of three coordinated layers: a primer, a thermoreflective functional layer and a weather-resistant top coat. Only the interplay of all three layers forms the complete system.

Adhesion, the insulating function and weather protection have different requirements. By dividing them among specialised layers, each performs its task optimally, while the layers are chemically and mechanically matched to one another.

The primer secures adhesion to the substrate, the functional layer provides the thermoreflective effect, and the top coat permanently protects the build-up against weathering and UV radiation.

To load-bearing, mineral and other suitable substrates (e.g. concrete, masonry, render). Substrate testing and preparation are described in Chapter 10.

On two complementary effects: part of the incident radiant heat is reflected at the surface (thermoreflection), and the hollow ceramic nanospheres embedded in the functional layer reduce heat conduction within the material.

The coating reflects a high proportion of the incident solar radiation across the entire spectrum, including infrared radiation (Total Solar Reflectance, TSR: 92 %). As a result, less radiant heat is transferred into the substrate.

The closed ceramic nanospheres, filled with vacuum or very little gas, form barriers to heat transport. In the tiny cavities the Knudsen effect takes hold — heat conduction through gas is practically suppressed (see Chapter 23 · Materials science).

Yes. The overall build-up is vapour-permeable (system value class V2 per EN 15824); water vapour from the component can escape to the outside. For the building-physics classification see Chapter 24.

The primer PSC 250 T ECB BASIC B, the thermoreflective functional layer PSC 250 T BUILD and the top coat PSC 250 T ECO OUTSIDE.

Primer approx. 0.1 mm, functional layer 1.0 mm (in two passes of 0.5 mm each) and top coat 0.1–0.2 mm — together a total thickness of approx. 1.2 mm. The figure of 1 mm stated in the technical data sheet refers to the functional layer.

Three coordinated PSCoat products: the primer ECB BASIC B, the functional layer BUILD and the top coat ECO OUTSIDE.

Each product has its own chapter with function, application and tested characteristic values per EN 15824 — see Chapters 07 (BASIC B), 08 (BUILD) and 09 (ECO OUTSIDE).

BASIC B is the primer (base coat) for all PSCoat main layers — BUILD, BUILD INTERIOR, ECI INTERIOR, ECO OUTSIDE, BS INSIDE, ECF FLOOR, BS FLOOR, ECE ELASTIC and ECR ROOF. It ensures the adhesion of the following layers and increases resistance to corrosion and water condensation; it can be applied directly to corroded but stable surfaces.

Water-based acrylic resin primer — non-toxic, harmless to health and environmentally compatible. Suitable for all interior and exterior construction surfaces made of concrete, cement, plaster bricks, wood, tar paper or plastic (except PE, HDPE, PP, PTFE).

Building materials such as concrete, cement, wood, tar paper, render and similar materials — including existing old stock (e.g. listed buildings), provided they are continuous and load-bearing. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and old loose coatings.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours.

BUILD is the conductive, thermoreflective insulating intermediate layer between the primer PSC 250 T ECB BASIC B and the top coat PSC 250 T ECO OUTSIDE. It effectively protects against penetrating frost or heat as well as against the condensation of surface water vapour and offers high adhesion on all common building materials.

Water-based acrylic resin coating — UV-resistant, vapour-permeable, non-toxic and environmentally friendly. It fills micro-cracks, prevents mould formation and does not dust off under atmospheric changes. BUILD reflects a high proportion of the incident solar radiation (Total Solar Reflectance, TSR: 92 %).

All porous surfaces such as concrete, masonry, stone, unglazed ceramics, render, gypsum or plasterboard — provided PSC 250 T ECB BASIC B has been applied beforehand as a primer. The substrate must be dry, firm, load-bearing and free of loose parts, oil, grease, dust, mould, salt and rust.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours.

ECO OUTSIDE is the decorative, thermoreflective top coat for the facades of residential and industrial buildings as well as for roof coverings. It withstands atmospheric influences and acid rain, is abrasion-resistant, vapour-permeable and permanently protects the underlying system build-up.

Water-based acrylic resin coating — UV-resistant and vapour-permeable. It reflects a high proportion of the incident solar radiation (Total Solar Reflectance, TSR: 92 %) and can be tinted in RAL colours in the COLOR version.

Porous, mineral substrates such as concrete, masonry, stone, unglazed ceramics, render, plasterboard, fibre cement or concrete tiles — on which the primer ECB BASIC B and the conductive intermediate layer BUILD have already been applied.

Supplied ready to use; thoroughly mix the entire container contents before use. As the finishing layer, preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours. Tinting only in the COLOR and SPECIAL COLOR versions.

Load-bearing, mineral and other porous substrates such as concrete, cement, masonry, stone, render, unglazed ceramics, plasterboard, fibre cement, concrete tiles, wood or tar paper — including old, load-bearing stock (e.g. listed buildings).

Dry, firm and load-bearing, and free of loose parts, oil, grease, dust, mould, salt and old, loose coatings. Loose or non-load-bearing old coatings must be removed.

The substrate moisture must be below 4 % (below 2.5 % for concrete). Measurement is carried out with a suitable moisture meter; if in doubt, wait until the substrate is ready to be coated.

By visual and wipe test (dust, sanding), scratch/tap test (voids) and — if in doubt — an adhesive pull-off or cross-cut test on the intended primer.

First the primer ECB BASIC B, then the functional layer BUILD and finally the top coat ECO OUTSIDE. Each layer must dry sufficiently before the next. The functional layer is applied in two passes of 0.5 mm (together 1.0 mm).

All products are supplied ready to use. Before use, thoroughly mix the entire container contents; thinning is not intended.

Preferably with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). Details on airless application in Chapter 12.

A further coat is possible once the surface is touch-dry after approx. 2 hours (overcoatable without sanding). Curing takes about 24 hours per layer.

Airless spraying applies the ready-to-use coatings evenly and economically — especially on larger facade areas. Brush and roller are possible as an alternative.

The filter must be removed before application (the coating contains ceramic nanospheres). The nozzle pressure must be limited to a maximum of 120 bar.

Even distance and path overlap to achieve a homogeneous layer thickness; maintain the intended thickness per layer (functional layer in 2 passes of 0.5 mm; see Chapter 05).

Immediately after use with water — the products are water-thinnable. Dried material is difficult to remove.

The substrate (strength, cleanliness, moisture) and the application conditions (temperature, humidity, weather) in accordance with Chapters 10 and 11.

The correct layer sequence, the consumption per layer and area, compliance with the intended thickness per layer, and drying before the next coat is applied.

By recording the substrate and weather conditions, the batches used, the consumption quantities and the application steps per area.

Even, closed layers without runs, defects or thin spots; a homogeneous, matt-white surface of the top coat.

PSCoat contains no substances classified as hazardous to health and is water-thinnable. The current safety data sheet is always decisive for the risk assessment.

Safety goggles, gloves and protective clothing. In confined spaces and when spraying, also use respiratory protection.

Ensure adequate ventilation and avoid or extract spray mist. Cover adjacent components and surfaces.

Clean tools with water — ideally immediately after use. Store and transport frost-free at +5 °C to +30 °C, protected from direct sunlight.

Yes. The top coat is abrasion-resistant, UV- and weather-resistant and vapour-permeable, and withstands atmospheric influences including acid rain.

Gently with water, at low pressure if needed. Aggressive cleaners, solvents or harsh mechanical methods must be avoided.

Local damage is cleaned, the substrate is checked as in Chapter 10, and the affected area is re-coated in the system build-up (primer, functional layer, top coat).

A regular visual inspection of the facade — especially after severe weather — is recommended in order to detect damage early.

Yes. The primer ECB BASIC B is the basis for the adhesion of BUILD and ECO OUTSIDE (Chapters 07, 11).

The top coat ECO OUTSIDE is available in RAL colours in the COLOR and SPECIAL COLOR versions (Chapter 09).

Yes, at any time. The thermoreflective top coat ECO OUTSIDE can also be re-tinted or changed in colour afterwards without any problem. To do so, a further, system-compatible coat of ECO OUTSIDE is simply applied in the desired RAL colour — without interfering with the existing system build-up and without impairing the insulating effect. The facade therefore remains permanently flexible: a new colour preference, adaptation to a changed design or a visual refresh are possible even years after the initial execution (Chapter 09).

At substrate and ambient temperatures of +5 °C to +30 °C and relative humidity below 80 % — not in rain, frost or on a substrate heated above +30 °C by direct sun (Chapter 11).

Not on PE, HDPE, PP, PTFE or other plastics (Chapter 10).

Yes, the overall build-up is vapour-permeable (system value class V2 per EN 15824); water vapour can escape to the outside (Chapter 04).

No. The λ values are system values and not a material characteristic per EN 12667/12664; for the building-physics classification see Chapter 24.

The stated λ values (e.g. 0.000120 W/mK) are system performance values , determined under defined test conditions (hot-box method). They do not correspond to the thermal conductivity of a material within the meaning of the standards EN 12667 or EN 12664.

No. It is a thermoreflective thin-film coating whose effect is based on radiation reflection and reduced heat conduction — not a volume-insulating material with a declared design value λ.

No. Since there is no material λ per EN 12667/12664, the system cannot simply be inserted into a U-value calculation. An energy verification per GEG is project-specific and must be carried out by a qualified person.

The overall build-up (primer + functional layer + top coat in combination) is vapour-permeable with a calculated system value of sd ≈ 0.44 m (class V2 per EN 15824) and has low water absorption (class W3). This is favourable for the moisture balance; the specific condensation protection must nevertheless be checked per object.

A washable, dirt- and chemical-resistant floor coating that thermally insulates the floor and withstands normal loads. ECF FLOOR serves residential, office and commercial areas, while BS FLOOR serves public buildings with bacteriostatic requirements such as hospitals, care homes and schools.

The primer PSC 250 T ECB BASIC B, the thermoreflective functional layer PSC 250 T BUILD INTERIOR and a floor coating — ECF FLOOR or BS FLOOR.

BASIC B is the primer for the functional layer PSC 250 T BUILD INTERIOR, on which the floor coating PSC 250 T ECF FLOOR or BS FLOOR is built. It ensures the adhesion of the following layer and increases resistance to corrosion and water condensation; it can be applied directly to corroded but stable surfaces.

Water-based acrylic resin primer — non-toxic, harmless to health and environmentally compatible. Suitable for floor surfaces made of concrete, cement or screed.

Building materials such as concrete, cement and similar materials — including old stock, provided it is continuous and load-bearing. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and old loose coatings.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours.

BUILD INTERIOR is the conductive, thermoreflective insulating intermediate layer between the primer PSC 250 T ECB BASIC B and the top coat PSC 250 T ECF FLOOR or BS FLOOR. It effectively protects against penetrating frost or heat as well as against the condensation of surface water vapour and offers high adhesion on all common building materials.

Water-based acrylic resin coating — UV-resistant, vapour-permeable, non-toxic and environmentally friendly. It fills micro-cracks, prevents mould formation and does not dust off under atmospheric changes. BUILD INTERIOR reflects a high proportion of the incident radiant heat (Total Solar Reflectance, TSR: 92 %).

All porous floor surfaces such as concrete, masonry, stone or unglazed ceramics — provided PSC 250 T ECB BASIC B has been applied beforehand as a primer. The substrate must be dry, firm, load-bearing and free of loose parts, oil, grease, dust, mould, salt and rust.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours.

ECF FLOOR is the thermoreflective floor coating for floors in residential, office and commercial areas without special hygiene requirements. It is fully washable, dirt- and chemical-resistant, withstands normal loads and effectively protects against penetrating frost or heat. For areas with bacteriostatic requirements, PSC 250 T BS FLOOR is used instead.

Water-based coating made of acrylic resin filled with ceramic nanospheres — UV-resistant, vapour-permeable, non-toxic and environmentally friendly; forms a membrane that covers micro-cracks. Can be tinted in RAL colours in the COLOR version.

Porous floor surfaces such as concrete, stone or unglazed ceramics — on which the primer PSC 250 T ECB BASIC B and the functional layer PSC 250 T BUILD INTERIOR have already been applied. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and rust.

Supplied ready to use; thoroughly mix the entire container contents before use. As the finishing layer, preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 200 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours. Tinting only in the COLOR and SPECIAL COLOR versions.

BS FLOOR is the bacteriostatic, thermoreflective floor coating for floors in public buildings such as hospitals, care homes or schools. It is fully washable, dirt- and chemical-resistant, withstands normal loads and effectively protects against penetrating frost or heat. For areas without bacteriostatic requirements, PSC 250 T ECF FLOOR is used instead.

Water-based coating made of acrylic resin filled with ceramic nanospheres — bacteriostatic, UV-resistant, vapour-permeable, non-toxic and environmentally friendly; forms a membrane that covers micro-cracks. Can be tinted in RAL colours in the COLOR version.

Porous floor surfaces such as concrete, stone or unglazed ceramics — on which the primer PSC 250 T ECB BASIC B and the functional layer PSC 250 T BUILD INTERIOR have already been applied. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and rust.

Supplied ready to use; thoroughly mix the entire container contents before use. As the finishing layer, preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 200 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours. Tinting only in the COLOR and SPECIAL COLOR versions.

The substrate must be dry, firm and load-bearing — free of loose parts, oil, grease, dust, mould, salt and rust. Mineral substrates are primed beforehand; the information in the respective product chapter prevails.

The coatings are supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand), alternatively with brush or roller (bristle length 8–14 mm). For airless application, add max. 0.1–0.3 litres of clean water.

Application at +5 °C to +30 °C and relative humidity below 80 %; not if rain or frost is expected. Stir the coating regularly during application, more frequently in direct sunlight.

A second coat is possible once the surface is touch-dry after approx. 2 hours; at least 24 hours between fully dried layers (max. 1.0 mm per layer). The cured surfaces are washable; clean tools with water.

The system reduces surface heat transfer indoors, improves condensation resistance and protects against dirt and mould. ECI INTERIOR serves residential and office buildings, while BS INSIDE serves public areas with bacteriostatic requirements.

The primer PSC 250 T ECB BASIC B, the thermoreflective functional layer PSC 250 T BUILD INTERIOR and a top coat — ECI INTERIOR or BS INSIDE.

BASIC B is the primer for the functional layer PSC 250 T BUILD INTERIOR as well as the interior coatings PSC 250 T ECI INTERIOR and PSC 250 T BS INSIDE. It ensures the adhesion of the following layers and increases resistance to corrosion and water condensation; it can be applied directly to corroded but stable surfaces.

Water-based acrylic resin primer — non-toxic, harmless to health and environmentally compatible. Suitable for interior surfaces made of concrete, cement, plaster bricks, wood or plastic (except PE, HDPE, PP, PTFE).

Building materials such as concrete, cement, wood, render and similar materials — including old stock (e.g. listed buildings), provided it is continuous and load-bearing. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and old loose coatings.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours.

BUILD INTERIOR is the conductive, thermoreflective insulating intermediate layer between the primer PSC 250 T ECB BASIC B and the top coat PSC 250 T ECI INTERIOR or BS INSIDE. It effectively protects against penetrating frost or heat as well as against the condensation of surface water vapour and offers high adhesion on all common building materials.

Water-based acrylic resin coating — UV-resistant, vapour-permeable, non-toxic and environmentally friendly. It fills micro-cracks, prevents mould formation and does not dust off under atmospheric changes. BUILD INTERIOR reflects a high proportion of the incident radiant heat (Total Solar Reflectance, TSR: 92 %).

All porous surfaces such as concrete, masonry, stone, unglazed ceramics, render, gypsum or plasterboard — provided PSC 250 T ECB BASIC B has been applied beforehand as a primer. The substrate must be dry, firm, load-bearing and free of loose parts, oil, grease, dust, mould, salt and rust.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours.

ECI INTERIOR is the decorative, thermoreflective interior coating for walls and ceilings of residential and office buildings. As interior insulation, it increases the reflection of the energy radiated back into the room from the surfaces, thereby reducing surface heat transfer. The treated surfaces are dirt-resistant, mould-resistant and have excellent condensation resistance.

Water-based coating made of acrylic resin filled with ceramic nanospheres — UV-resistant, vapour-permeable, non-toxic and environmentally friendly; forms a membrane that covers micro-cracks. It reflects a high proportion of the incident solar radiation (Total Solar Reflectance, TSR: 92 %) and can be tinted in RAL colours in the COLOR version.

Porous interior surfaces such as concrete, masonry, stone, unglazed ceramics, render or plasterboard — on which the primer PSC 250 T ECB BASIC B and the functional layer PSC 250 T BUILD INTERIOR have already been applied. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and rust.

Supplied ready to use; thoroughly mix the entire container contents before use. As the finishing layer, preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 200 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours. Tinting only in the COLOR and SPECIAL COLOR versions.

BS INSIDE is the bacteriostatic, thermoreflective interior coating for public areas — such as hospitals, care homes or schools. It is dirt- and mould-resistant as well as bacteria-inhibiting and, as interior insulation, increases the reflection of the energy radiated back into the room. The treated surfaces have excellent condensation resistance.

Water-based coating made of acrylic resin filled with ceramic nanospheres — bacteriostatic, UV-resistant, vapour-permeable, non-toxic and environmentally friendly; forms a membrane that covers micro-cracks. Can be tinted in RAL colours in the COLOR version.

Porous interior surfaces such as concrete, masonry, stone, unglazed ceramics, render or plasterboard — on which the primer PSC 250 T ECB BASIC B and the functional layer PSC 250 T BUILD INTERIOR have already been applied. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and rust.

Supplied ready to use; thoroughly mix the entire container contents before use. As the finishing layer, preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 200 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours. Tinting only in the COLOR and SPECIAL COLOR versions.

The substrate must be dry, firm and load-bearing — free of loose parts, oil, grease, dust, mould, salt and rust. Mineral substrates are primed beforehand; the information in the respective product chapter prevails.

The coatings are supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand), alternatively with brush or roller (bristle length 8–14 mm). For airless application, add max. 0.1–0.3 litres of clean water.

Application at +5 °C to +30 °C and relative humidity below 80 %; not if rain or frost is expected. Stir the coating regularly during application, more frequently in direct sunlight.

A second coat is possible once the surface is touch-dry after approx. 2 hours; at least 24 hours between fully dried layers (max. 1.0 mm per layer). The cured surfaces are washable; clean tools with water.

The system protects roofs from weathering and reduces heat transfer. Depending on the substrate, different layers are used: mineral coverings, elastic materials and steel roofs.

The primers PSC 250 T ECB BASIC A (metal) and ECB BASIC B (mineral), the insulating functional layer PSC 250 T HP+, and a reflective finishing layer — ECE ELASTIC or ECR ROOF.

BASIC A is the primer for metal roofs — it prepares steel roofs for the functional layer PSC 250 T HP+ and the top coat PSC 250 T ECR ROOF. It ensures the adhesion of the following layers and increases resistance to corrosion and water condensation; it can be applied directly to corroded but stable metal surfaces.

Water-based acrylic resin primer — non-toxic, harmless to health and environmentally friendly. Specifically for metal substrates such as steel, aluminium, stainless steel or copper.

All surfaces made of steel, aluminium, stainless steel, copper and similar metals — these may be rusty but must be continuous. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and old loose coatings.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours.

BASIC B is the primer for mineral roof coverings — it prepares concrete, tile or render substrates for the functional layer PSC 250 T HP+ and the top coat PSC 250 T ECE ELASTIC. It ensures the adhesion of the following layers and increases resistance to corrosion and water condensation; it can be applied directly to corroded but stable surfaces.

Water-based acrylic resin primer — non-toxic, harmless to health and environmentally compatible. Suitable for mineral roof coverings made of concrete, cement, plaster bricks, wood, tar paper or plastic (except PE, HDPE, PP, PTFE).

Building materials such as concrete, cement, wood, tar paper, render and similar materials — including old stock, provided it is continuous and load-bearing. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and old loose coatings.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours.

HP+ is the insulating functional layer between the primer (PSC 250 T ECB BASIC A or BASIC B) and the top coat (PSC 250 T ECE ELASTIC or ECR ROOF). It reduces the surface temperature of the roof and can reduce energy costs for cooling or heating.

Water-based acrylic resin coating with the highest ceramic-nanosphere content in the product line; contains corrosion-protection components. High resistance to chemical environments and weathering; reflects a high proportion of the incident solar radiation (Total Solar Reflectance, TSR: 92 %).

Metal roofs primed with PSC 250 T ECB BASIC A, or mineral roof coverings primed with PSC 250 T ECB BASIC B. The substrate must be dry, firm, free of oil, grease, dust, salt, rust and old loose coatings.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 130 bar), alternatively with brush or roller (bristle length 8–14 mm). Layers of 0.5–5 mm are recommended (one layer max. 1 mm). HP+ is applied as an intermediate layer; ECE ELASTIC or ECR ROOF follow as the finishing layer.

ECE ELASTIC is the elastic, thermoreflective finishing coat for roof coverings and construction elements made of PVC, PC, PS, asphalt strips (IPA), plastic, polycarbonate or hardened PVC. It withstands weathering and acid rain and permanently protects the substrate.

Water-based acrylic resin coating with elastomeric properties — abrasion-resistant, vapour-permeable, UV-resistant and with increased resistance to mechanical damage. It reflects a high proportion of the incident solar radiation (Total Solar Reflectance, TSR: 92 %) and can be tinted in RAL colours in the COLOR version.

Elastic materials (PVC, PC, PS, asphalt sheeting, polycarbonate) as well as porous substrates such as concrete, masonry, stone, unglazed ceramics, render or plasterboard — on porous substrates after priming with PSC 250 T ECB BASIC B. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and rust.

Supplied ready to use; thoroughly mix the entire container contents before use. As the finishing layer, preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours. Tinting only in the COLOR and SPECIAL COLOR versions.

ECR ROOF is the flexible, thermoreflective top coat for steel roofs and roof construction elements with a slope of more than 3 %. It serves as a top coat for HP and HP+ or as a standalone reflective finishing layer. The coating is fully washable, dirt- and chemical-resistant and highly resistant to weathering.

Water-based acrylic resin coating with excellent protective and visual function and high resistance to chemical environments of classes C4 and C5. It reflects a high proportion of the incident solar radiation (Total Solar Reflectance, TSR: 92 %) and can be tinted in RAL colours in the COLOR version.

Surfaces made of steel, aluminium, stainless steel or copper, on which the primer PSC 250 T ECB BASIC A or one of the insulating coatings HP or HP+ has already been applied. The coating can also be used standalone as a reflective finishing layer without HP or HP+.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours. Tinting only in the COLOR and SPECIAL COLOR versions.

The substrate must be dry, firm and load-bearing — free of loose parts, oil, grease, dust, mould, salt and rust. Mineral substrates are primed beforehand; the information in the respective product chapter prevails.

The coatings are supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand), alternatively with brush or roller (bristle length 8–14 mm). For airless application, add max. 0.1–0.3 litres of clean water.

Application at +5 °C to +30 °C and relative humidity below 80 %; not if rain or frost is expected. Stir the coating regularly during application, more frequently in direct sunlight.

A second coat is possible once the surface is touch-dry after approx. 2 hours; at least 24 hours between fully dried layers (max. 1.0 mm per layer). The cured surfaces are washable; clean tools with water.

The system reduces the surface temperature of steel structures, stabilises operation and can significantly reduce energy costs for cooling or heating. It offers high resistance to chemical environments of classes C4 and C5. Applications include pipework, tanks, heat exchangers, containers and roofs.

The metal primer PSC 250 T ECB BASIC A, the insulating main coating PSC 250 T HP+ and the reflective top coat PSC 250 T EC+ — with HP+ also usable without a primer.

BASIC A is the primer (base coat) for the industrial main layers HP, HP+, EC, EC+ and ECR ROOF. It ensures the adhesion of the following layers and increases resistance to corrosion and water condensation; it can be applied directly to corroded but stable metal surfaces.

Water-based acrylic resin primer — non-toxic, harmless to health and environmentally friendly. Specifically for metal substrates such as steel, aluminium, stainless steel or copper.

All surfaces made of steel, aluminium, stainless steel, copper and similar metals — these may be rusty but must be continuous. The substrate must be dry, firm and free of loose parts, oil, grease, dust, mould, salt and old loose coatings.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours.

HP+ is the insulating main and sealing coating for steel structures, plant and equipment — both indoors and outdoors. It reduces the surface temperature, stabilises the operation of equipment and can reduce energy costs for cooling or heating by up to 50 %. Typical application areas are hot and cold water pipes, air conditioning systems, freezers, steam pipes and boilers, tanks, heat exchangers and containers.

Water-based acrylic resin coating with the highest ceramic-nanosphere content in the product line; contains corrosion-protection components and can therefore be used without the primer ECB BASIC A. High resistance to chemical environments of classes C4 and C5, to condensation and weathering; reflects a high proportion of the incident solar radiation (Total Solar Reflectance, TSR: 92 %).

All metal surfaces made of steel, aluminium, stainless steel or copper — even without prior priming with ECB BASIC A. The substrate must be dry, firm, free of oil, grease, dust, salt, rust and old loose coatings.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 130 bar), alternatively with brush or roller (bristle length 8–14 mm). Layers of 0.5–5 mm are recommended (one layer max. 1 mm). HP+ is applied as an intermediate or base layer; the finishing layer follows with ECR ROOF, EC or EC+.

EC+ serves as a reflective top coat for the coatings HP and HP+ outdoors and can also be used as a standalone reflective finishing coat. Application areas are exterior surfaces of structures, plant or equipment. The coating is fully washable, dirt- and chemical-resistant and highly resistant to atmospheric influences.

Water-based acrylic resin coating with excellent protective, reflective and visual function; high resistance to chemical environments of classes C4 and C5. Thanks to corrosion-protection components, usable without the primer ECB BASIC A; reflects a high proportion of the incident solar radiation (Total Solar Reflectance, TSR: 92 %) and can be tinted in RAL colours in the COLOR version.

All metal surfaces made of steel, aluminium, stainless steel or copper, on which ECB BASIC A or one of the insulating coatings HP or HP+ has already been applied as a primer. The coating can also be used as a standalone finishing coat without HP, HP+ or ECB BASIC A.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 120 bar), alternatively with brush or roller (bristle length 8–14 mm). A second coat is possible once the surface is touch-dry after approx. 2 hours. Tinting only in the COLOR and SPECIAL COLOR versions.

The substrate must be dry, firm and load-bearing — free of loose parts, oil, grease, dust, mould, salt and rust. Mineral substrates are primed beforehand; the information in the respective product chapter prevails.

The coatings are supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand), alternatively with brush or roller (bristle length 8–14 mm). For airless application, add max. 0.1–0.3 litres of clean water.

Application at +5 °C to +30 °C and relative humidity below 80 %; not if rain or frost is expected. Stir the coating regularly during application, more frequently in direct sunlight.

A second coat is possible once the surface is touch-dry after approx. 2 hours; at least 24 hours between fully dried layers (max. 1.0 mm per layer). The cured surfaces are washable; clean tools with water.

Nanobrandschutzdämmung combines thermal insulation with the protection of steel structures. The coating reduces the surface temperature, is highly resistant to chemical environments of classes C4 and C5, and is suitable for interior and exterior areas of industrial structures, plant and equipment.

The insulating main coating PSC 1200 T HP+, which — thanks to its corrosion-protection components — can be applied directly to steel, even without a separate primer; if required, PSC 250 T ECB BASIC A serves as a primer.

PSC 1200 T HP+ is the insulating main and sealing coating for steel structures, plant and equipment — both indoors and outdoors. It reduces the surface temperature, stabilises the operation of equipment and can reduce energy costs for cooling or heating by up to 50 %. Typical application areas are hot and cold water pipes, air conditioning systems, freezers, steam pipes and boilers, tanks, heat exchangers and containers.

Water-based acrylic resin coating with the highest ceramic-nanosphere content in the product line; contains corrosion-protection components and can therefore be used without a separate primer. High resistance to chemical environments of classes C4 and C5, to condensation and weathering; reflects a high proportion of the incident solar radiation (Total Solar Reflectance, TSR: 92 %).

All metal surfaces made of steel, aluminium, stainless steel or copper — even without prior priming with ECB BASIC A. The substrate must be dry, firm, free of oil, grease, dust, salt, rust and old loose coatings.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 130 bar), alternatively with brush or roller (bristle length 8–14 mm). Layers of 0.5–5 mm are recommended (one layer max. 1 mm).

The substrate must be dry, firm and load-bearing — free of loose parts, oil, grease, dust, salt and rust. Thanks to its corrosion-protection components, PSC 1200 T HP+ can be applied directly to steel; priming with ECB BASIC A is optional.

Supplied ready to use; thoroughly mix the entire container contents before use. Preferably applied with an airless sprayer (remove the filter beforehand, nozzle pressure max. 130 bar), alternatively with brush or roller (bristle length 8–14 mm). Layers of 0.5–5 mm are recommended (one layer max. 1 mm).

Ambient temperature +5 °C to +30 °C and relative humidity below 80 %; not if rain or frost is expected. The coating can be applied to hot surfaces up to +220 °C during operation.

A second coat is possible once the surface is touch-dry after approx. 2 hours; at least 24 hours between fully dried layers (max. 1.0 mm per layer). Clean tools with water.